#How to build a usb pic programmer manual#
#How to build a usb pic programmer software#
#How to build a usb pic programmer download#

PIC Programmer is an essential tool if you wish to learn or build a project that uses Microchip PIC Micro Processors such as DDS, Repeater Controllers and LCD Power Meter. An hi-res version of this picture is available HEREВ for being printed and attached on the back of the programmer itself.Technical Details & Assembly Note: USB PIC Programmer The PIC to be programmed has to be positionned on the ZIF socket as shown by the following picture. That voltage is anyway already verified by the firware itself. The test functions allow to measure the Vpp high voltage generated by the step-up converter present on the main circuit.

#How to build a usb pic programmer software#

The PC software allows bot writing and reading the EEPROM of any PIC mounted on the ZIF socked. Than slowly, indicating that the connection phase is completed. The green led blinks speedy first, announcing the connection in progress. hex file on the link below вЂ“ OProg.hex UsageД¬onnect the programmer to the PC with a male-male A-Type USB cable.

#How to build a usb pic programmer download#

You can download the PC software on the link below вЂ“ OpenProg.rar After that first step, you will be automous! Of course, if you have not a programmer yet, a friend should program the programmer first, for you. After some tests, you can try the new updated versions available on the original site. Anyway, to start using this programmer, I suggest you to use the versions I used at time of project editing, available hereafter for downloading. The first PCB has to be fixed on the box using the supplied screws.ДЄs said before, the original site offers both the firmware and the PC side software.

The cover has a border that shall be modified to host the circuits, but your logic will drive you. It is a A-type female The BoxДЄfter a few attempts and corrections you will reach the final result. You shall create holes to let emergent parts to exit from its surface: the socket, the two leds (or a single bi-colour led), the USB socket on a short side. Just the socket and the two leds shall emerge. Use countersunk screws of countersunk holes to avoid the screws being too hight respect to upper surface of second PCB. Once the two circuits are ready, connect them using the strip lines, and block assembly using the columns. During soldering jump several pins each time, following a spiral line, adopting a sequence that allow to warm-down a pin while you are soldering the next one.

It is better to do 1.2 mm holes to facilitate the insertion ofВ the ZIF socket in the PCB. Pay attention to avoid any force that can lead to damage or deformation. The ZIFВ is a quite delicate component befor final soldering.

#How to build a usb pic programmer manual#

Use low profiles parts to fix the columns, otherwise some manual metals removal can be needed to reduce the occupation on the copper side. Mount 4 ten millimeters height columns to allow the final assembly of the second board. SchematicД«uild first the main module using low profile components being under 10 mm of height from the PCB surface, since a second board will be mounted over that one. Take into account that, on the original site, a newer version of both Firmware and Software is available. I tested the program up to Win-8 without problems. At the bottom of this page, I supply a copy of the program to load on the PIC18F2550 used to manage the programming functions, as well as a copy of the PC side program. Hereafter, I shown my Compact version, with a schematic, PCB layout and instruction for assemby and inserting it in a very common little plastic box. The details are available on the original project mentionned above. Anyway, if your goal is to program PIC devices, you are on the good site.ДЄ small box, a USB connector, a ZIF socket, two leds. I will thank everybody proposing a larger range implementation, suitable to program Atmel and other devices. This version sacrifices many non-PIC microcontroller models. So, I propose here a small layout version of that circuit, adopting a single smart on-board ZIF socket.

Moreover, the proposed layout did not meet my personal вЂњcompact lookвЂќ ideas. What concerned me was the need to mount, on the mainboard, a specific socket board depending on the model of PIC being programmed. Looking on the web for ready-to-use projects, I found a good one called Open Programmer, coming with several schematics, PCBs and Open Source code.

This page is dedicated to everybodyВ needs to program a PIC (Microchip) device via USB port.